Head gasket blown - Thermaseal type quick fix?
#1
Scooby Regular
Thread Starter
Join Date: Jan 2000
Location: Disco, Disco!
Posts: 21,825
Likes: 0
Received 0 Likes
on
0 Posts
Head gasket blown - Thermaseal type quick fix?
Hi All,
Head gasket is likly got a slight blow - oil to water - small amount of creamy cr@p in the tank, nothing to bad.
Replacing the rad tomorrow which is the likely cause of the problem.
Are any od the pour-in type remedies any good?
My main issue is that the blow will push whatever sealant i put in away as the oil is under pressure and blowing into the water if you see what i mean
The car in question is my old Pug 406 TD sh*tter worth not a lot so do not want to spend good money after bad.
The car needs to last for 12 months or so and around 12k miles and i will likely scrap it.
some of the prods
RxAuto Head Gasket Repair | Blown Head Gasket | Call 1-866-780-9042
Bar's Leaks Head Gasket Repair
Steel Seal- RETAIL CUSTOMERS
Any reccomendations or any to steer away from?
I know i could poist in OM but is it a general question about this stuff rather than car specific if you see what i mean.
Head gasket is likly got a slight blow - oil to water - small amount of creamy cr@p in the tank, nothing to bad.
Replacing the rad tomorrow which is the likely cause of the problem.
Are any od the pour-in type remedies any good?
My main issue is that the blow will push whatever sealant i put in away as the oil is under pressure and blowing into the water if you see what i mean
The car in question is my old Pug 406 TD sh*tter worth not a lot so do not want to spend good money after bad.
The car needs to last for 12 months or so and around 12k miles and i will likely scrap it.
some of the prods
RxAuto Head Gasket Repair | Blown Head Gasket | Call 1-866-780-9042
Bar's Leaks Head Gasket Repair
Steel Seal- RETAIL CUSTOMERS
Any reccomendations or any to steer away from?
I know i could poist in OM but is it a general question about this stuff rather than car specific if you see what i mean.
#2
Scooby Regular
Join Date: Mar 2000
Location: Weston Super Mare, Somerset.
Posts: 14,102
Likes: 0
Received 0 Likes
on
0 Posts
Why would a duff rad cause a gasket problem??
I had similar probs with a 205 tdi and we tried various fixes. Main thing was to check water level daily and top up. It used gallons of water but still ran well My main concern was no water and consequent seizure.
In the end I got a new head gasket but an expensive job with a turbo bolted on in labour terms.
I'd say try the fixes first and it might be OK. If not - well pay up or scrap!! david
PS. Isn't that a USA number at top of list
I had similar probs with a 205 tdi and we tried various fixes. Main thing was to check water level daily and top up. It used gallons of water but still ran well My main concern was no water and consequent seizure.
In the end I got a new head gasket but an expensive job with a turbo bolted on in labour terms.
I'd say try the fixes first and it might be OK. If not - well pay up or scrap!! david
PS. Isn't that a USA number at top of list
#3
Scooby Regular
iTrader: (1)
Join Date: Jun 2007
Location: throwing pieces oot a 20 storey flat
Posts: 1,845
Likes: 0
Received 0 Likes
on
0 Posts
peugeot TD engines are a nightmare for head gaskets,dont ever let it overheat,carry plenty of water wherever you go.They warp cylinder heads very very quickly
#4
Scooby Regular
Join Date: Dec 2002
Location: Couch Spud
Posts: 9,277
Likes: 0
Received 0 Likes
on
0 Posts
Got a similar problem with the Toyota Previa, and was looking around at some products
one of the cylinders is letting water in, so is misfiring on start, and quite a bit of smoke (unless I drive it every day) but runs ok when running and warm
only paid 950 for it, and its 500 for head gasket replacement, I know they mentioned a product over on the Shogun forums that is supposed to be pretty good but the name eludes me for the moment (it is from the states too I believe)
Mine is losing about 3 pints of water for 5-10 mile trips from cold
one of the cylinders is letting water in, so is misfiring on start, and quite a bit of smoke (unless I drive it every day) but runs ok when running and warm
only paid 950 for it, and its 500 for head gasket replacement, I know they mentioned a product over on the Shogun forums that is supposed to be pretty good but the name eludes me for the moment (it is from the states too I believe)
Mine is losing about 3 pints of water for 5-10 mile trips from cold
#5
Scooby Regular
Join Date: May 2004
Location: Ascended to the next level
Posts: 7,498
Likes: 0
Received 0 Likes
on
0 Posts
Could always try putting a touch more torque on the head bolts*
Tighten in a cris-cross patten. Like you should do with wheel nuts.
*will not be held responsible if a bolt shears off
Pug 1.9 diesels are common for it. Lack of coolant changes is the main curlprit - old acidic coolant eats the gasket. Simple job, somewhat labour intensive as its typically French with everything being positioned in a ****-eyed manner. Not as bad as doing the same engine in a Pug Expert van....bad back anyone?
Tighten in a cris-cross patten. Like you should do with wheel nuts.
*will not be held responsible if a bolt shears off
Pug 1.9 diesels are common for it. Lack of coolant changes is the main curlprit - old acidic coolant eats the gasket. Simple job, somewhat labour intensive as its typically French with everything being positioned in a ****-eyed manner. Not as bad as doing the same engine in a Pug Expert van....bad back anyone?
Trending Topics
#8
Scooby Regular
Join Date: May 2004
Location: Ascended to the next level
Posts: 7,498
Likes: 0
Received 0 Likes
on
0 Posts
Never worked on one. Done a few Bedford/Isuzu Midis and LDV/Nissan cubs/vannetes, and despite being mid-engined, its dooable as the access hatch is big enough or the entire seat box can be removed.
Just googled and found pic of previa access - oh dear looks like engine has to be dropped out from underneath, or dropped down onto axle stands/ blocks to get enough access to it.
Something tells me Toyota didn't quite think the design through very well with teh Previa Oh well, Espace is no better, and they go wrong a lot more often
#9
Scooby Regular
Join Date: Dec 2002
Location: Couch Spud
Posts: 9,277
Likes: 0
Received 0 Likes
on
0 Posts
Cheers Ali
I did have the drivers seat out and access panel (ttok bleddy ages) so I could change the spark plugs thinking it was those originally
Yes not the best thought out layout, but then I have no idea if they changed the access on the newer generation models (mine is the 1st generation 1996 model)
I did have the drivers seat out and access panel (ttok bleddy ages) so I could change the spark plugs thinking it was those originally
Yes not the best thought out layout, but then I have no idea if they changed the access on the newer generation models (mine is the 1st generation 1996 model)
Thread
Thread Starter
Forum
Replies
Last Post
Bazil_SW
Engine Management and ECU Remapping
24
21 September 2015 11:55 PM